VHB 3M 5608 Double Sided Adhesive Acrylic Foam Tape Sticker Mounting Gray 100mm*100mm*0.8mm |

VHB 3M 5608 Double Sided Adhesive Acrylic Foam Tape Sticker Mounting Gray 100mm*100mm*0.8mm |

Description

VHB 3M 5608 Double Sided Adhesive Acrylic Foam Tape Mounting Tape Gray 100mm*100mm*0.8mm

Up for sale is 100mmx100mm 3M 5608a sticker

• Size: 100mmx100mm

• Thickness: around 0.8mm

• Color: Grey

• VHB: Very High Bond

• More than 2lots in 1 buy get more than 5% off

• More buy get more discount, large quanity, please contact.

• Fee shipping with online tracking No.

• 48 hours ship out

How to use this tape?
Clean: For maximum bond strength,the surface must be clean, dry, smooth, have no rust and oil pollution.Typical cleaning solvents are heptane or isopropyl alcohol.
Pressure: Pressure on the adhesive and the surface can help improve bond strength, roller or platen can be used.
Time: After application, the bond strength will increase as the adhesive flows onto the surface. At room temperature approximately 50% of ultimate bond  strength will be achieved after 20 minutes, 90% after 24 hoursand 100% after 72 hours.
Temperature:Ideal application temperature range is 70°F to 100°F (21degree centigrade to 38degree centigrade).Operating temperature should not be below 10 degree centigrade, the temperature is too low, will lead to cure time longer. If temperature is too low, move material and adhesive tape into the warm indoor storage or heating treatment.

Q. What percent of the final bond strength can I expect immediately after application? After 24 hours?  After 72 hours?
A. Immediately after an application is made, about 60% of the bond strength is achieved. As the adhesive continues to wet-out the surface, you can expect the bond to be at about 75% - 80% after 24 hours. After 72 hours, 95%+ of the bond strength is achieved. The bond will continue to build with time.

Q. Is the tape solvent resistant?
A. Yes, 3M acrylic foam tapes are resistant to most common automotive solvents like gasoline, diesel fuel, washer solvent, etc. Solvent resistance is a function of type of solvent, time of exposure and temperature.

Q. Why doesn`t the tape feel sticky?
A. 3M`s high performance acrylic adhesives tend to be firm and dry to the touch. They are designed to bond materials other than skin. The adhesives used are designed to give optimum performance and adhesion to automotive substrates and components. The natural oils and moisture of skin can vary from person to person and affect the "thumb appeal" of the 3M Acrylic Foam Tape. To one person the tape can feel very sticky and to another it can feel much less sticky to the touch. The difference in "thumb appeal" is in the variation of the 2 individual`s skin surfaces not the adhesive.

Q. The part is not adhering to the vehicle. What might be wrong?
A. Areas to investigate for poor adhesion or performance include:
Check for surface contamination. The substrates must be clean and free of any contaminant. This is the most common cause of poor adhesion.
Check for surface match. Are the two surfaces to be bonded a good match?
Check for proper application pressure and wet-out.
Check the back of the component for flatness.
Check the installation process for proper procedures

• Grey color, very high bond

• Widely using for automobile, home parts, daily life, etc...

• Ideal tape application temperature range is 70°F to 100°F (21°C to38°C).

• To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified.

• Bond strength is dependent upon the amount of adhesive-to-surface contact developed.

• Firm application pressure helps develop better adhesive contact and improves bond strength.

IMPORTANT!

• Picutre only for reference, really tape is as per actual width tape, thanks.

• The yellow parts in the picture is for help take photo, not including in the sale.

• We can cut as your request other width.

• Die-cutting accept with MOQ.

• 
  

• 
  

• 
  

• According to choose